Novatron

Information Novatron Requires:

When enquiring about a water desalination machine:

1. Is your water supply Brackish Water or Sea Water?
2. If your enquiry is regarding Brackish Water do you have a Water Analysis? (We do not require an Analysis if your enquiry is regarding Sea Water.)
3. How much Water can the Bore or source of supply deliver per hour?
4. What is your daily water usage requirement?
5. Information regarding your power supply, e.g single or three phase etc.

Procedure for Testing of Water Source

Your water needs to be tested using the following procedures before coming to Novatron:

1. Water Source should be run continuously for a minimum of 1 hour with best results after 3 hours.
2. Keeping the flow going, fill a clean container such as a plastic bucket and place a clean sample container completely under water. This is to ensure that as little as possible surface water enters the container.
   
   Pour some of the water out if necessary to end up with 10% air and 90% water in the container before closing the lid (preferably screw top) firmly.
   
   Please note that due to the wide range of test parameters the laboratory requires at least 1 litre of water.
3. Forward the sample as soon as possible to MPL Laboratories at one of the following addresses.
   
   Please advise Novatron befrore you despatch your sample so that we may ensure that your sample receives immediate attention.
   
   Label your water sample clearly as indicated below.
   
   Client: Novatron
   
   Type: Novatron Analysis
   
   Sample ID: (Your Name & Address & Telephone Number)
   
   Novatron will invoice you for your analysis to enable you to take advantage of our quantity discount.

MPL Laboratories

Western Australia Attention: Ms. Janine Steven 16-18 Hayden Court Myaree 6154	Ph: +61 8 9317 2505 Fax: +61 8 9317 4163 Email: laboratory@mpl.com.au
South Australia Attention: Mr. Rodney Fox Commerce & Research Precinct Universty of Adelaide 26 Anderson Street Thebarton 5031	Ph: +61 8 8443 8000 Fax: +61 8 8443 8003 Email: mplsa@mpl.com.au
New South Wales Attention: Mr. Conrad Winter Level 18, Citigroup Centre 2 Park Street Sydney 2000	Ph: +61 2 9262 9444 Fax: +61 2 9262 9400 Email: mplnsw@mpl.com.au

Web Site: www.mpl.com.au

Please ask for a Novatron Water Analysis

The reason for this is that this laboratory has on file the necessary parameters and specifications, as supplied by the manufacturers of the filtration membranes, to give us the information we require to provide you with the best possible advice. This also enables us to pass on to you our 'quantity' discount when we invoice you for your water analysis.

Parameters for Testing of water Source

Test Parameters of a "Novatron" Water Analysis TEST PARAMETERS UNIT LQL Electrical Conductivity uS/cm 1 Total Dissolved Solids mg/L 1 pH pH Units 0.05 Turbidity NTU 0.1 TurbidityFiltered (Whatman 40) NTU 0.1 Colour True HZU 1 Iron, Fe (Soluble) mg/L 0.01 Iron (Total), Fe mg/L 0.01 Hardness mg/L 1 Hydrogen Sulphide, H2S mg/L 0.01 Calcium, Ca mg/L 0.1 Magnesium, Mg mg/L 0.1 Sodium, Na mg/L 1 Potassium, K mg/L 0.1 Ammonium as N mg/L 0.05 Barium, Ba mg/L 0.001 Strontium, Sr mg/L 0.005 Carbonate, CO3 mg/L 1 Bicarbonate, HCO3 mg/L 1 Sulphate, SO4 mg/L 1 Chloride, Cl mg/L 1 Flouride, F mg/L 0.1 Nitrate, NO3 mg/L 0.1 Silica, Si02 mg/L 0.2 Hydroxide, OH mg/L 1 Boron, B mg/L 0.05

NOTES:
LOR- Limit of Reporting

A typical analysis meeting all the required parameters IDENT External ident ANALYTE UNITS LQL M001 M Windmill Electrical Conductivity uS/cm 1 16000 Total Dissolved Solids mg/L 1 10000 pH pH Units 0.05 5.95 Turbidity NTU 0.1 0.1 TurbidityFiltered (Whatman 40) NTU 0.1 0.1 Colour True HZU 1 3 Iron, Fe (Soluble) mg/L 0.01 0.02 Iron (Total), Fe mg/L 0.01 0.03 Hardness mg/L 1 2200 Hydrogen Sulphide, H2S mg/L 0.01 <0.01 Calcium, Ca mg/L 0.1 67 Magnesium, Mg mg/L 0.1 500 Sodium, Na mg/L 1 2600 Potassium, K mg/L 0.1 64 Ammonium as N mg/L 0.05 0.07 Barium, Ba mg/L 0.001 0.095 Strontium, Sr mg/L 0.005 2.2 Carbonate, CO3 mg/L 1 <1 Bicarbonate, HCO3 mg/L 1 30 Sulphate, SO4 mg/L 1 920 Chloride, Cl mg/L 1 5300 Flouride, F mg/L 0.1 <0.4 Nitrate, NO3 mg/L 0.1 79 Silica, Si02 mg/L 0.2 120 Hydroxide, OH mg/L 1 <1 Boron, B mg/L 0.05 3.4